Reed Roofing

Flat Roofing November 16, 2026 Reed Roofing Team

Modified Bitumen Roof Blisters: Why Is My Flat Roof Bubbling?

Modified bitumen roof blisters form where the membrane is not fully bonded to the layer beneath it. Air or moisture sits in that small void, the sun heats the roof, the trapped pocket expands, and the membrane lifts into a bubble. Many blisters are stable and can simply be watched, but one that is cracked, growing, or sitting on a seam needs a roofer to look at it.

The sections below explain how voids and moisture lead to blistering, what a roofer checks, how to record a blister so changes are easy to see, and which findings lead to a recommendation to monitor or repair.

Bubbles on a flat roof membrane start with a spot that did not bond. Modified bitumen is installed in sheets over a base sheet, insulation board, or the roof deck. Wherever a sheet did not adhere completely, a void is left that holds air and often some moisture. As the roof heats up, the air and vapor expand and push the membrane upward. At night the pocket cools and relaxes. Repeated daily, that cycle can stretch the membrane and let the blister grow. The void and the moisture can come from:

What causes bubbles on a modified bitumen roof?

  • Incomplete adhesion when the sheet was installed.
  • Dust, debris, or dampness on the surface when the membrane was laid.
  • Moisture already in the insulation or deck when the roof was covered.
  • Water entering later through an open seam, a puncture, or failed flashing.
  • Moisture rising from inside the building into the roof assembly.

The first three are mostly a surface condition. The last two mean water is getting into the roof, and bituminous roof blistering is then a symptom of a larger problem.

Are blisters on a flat roof a serious problem?

It depends on the blister. An intact blister is still watertight, because the membrane has stretched but not opened. The concern is what happens next. A raised membrane loses its protective granules sooner, ages faster in the sun, and can crack. A blister that breaks open is a hole in the roof.

Location matters as much as size. A blister in the open field of the roof is the lowest risk. One that reaches a seam can pull the lap apart, one in a walking path can be crushed underfoot, and one in a low spot stays wet longer after every rain.

What does a roofer check around a blister?

A roofer looks at the blister, the seams near it, and the layers below it, to learn whether it is a sealed pocket of air or a sign of water in the roof. During a <a href="https://srreedroofing.com/services/modified-bitumen-roofing">modified bitumen roof assessment</a>, the main points are:

  • Seams and laps: whether the blister touches a seam and whether nearby lap edges are lifted or open.
  • Surface damage: cracks, splits, punctures, and bare areas where the granules have worn off.
  • The feel of the blister: firm and dry, or soft and spongy, which can point to water inside.
  • The roof assembly underneath: soft or uneven spots that suggest wet insulation or a damaged deck.
  • Drainage: whether water ponds at the blister and whether nearby drains are clear.
  • Flashings and penetrations close by where water could be entering.
  • The ceiling below: stains or damp areas under that part of the roof.

How should you record a roof blister and track changes?

Keep a dated record. It shows whether a blister is stable or growing, which is hard to judge from one visit. Only do this if the roof can be reached safely. If not, photos from a window or upper floor still help.

  • Mark each blister on a simple sketch of the roof, with its distance from a fixed point such as a drain or vent.
  • Measure its length and width and write them down with the date.
  • Photograph it with a tape measure in the frame for scale.
  • Take photos at a similar time of day. Blisters are fuller in afternoon heat and flatter on a cool morning.
  • Note the surface condition and whether water stands on it after rain.
  • Repeat every few months and after long hot spells.

Do not step on a blister, press on it, or cut it to let the air out. Each can turn a sealed bubble into a leak. Blister checks fit into a regular upkeep routine, and this guide on <a href="https://srreedroofing.com/blog/maintain-your-flat-roof">how to maintain your flat roof</a> covers what else to look at on the same visit.

When is a blister monitored and when is it repaired?

Monitoring makes sense when the inspection shows a sealed blister on an otherwise sound roof. Cutting into an intact membrane to fix a harmless bubble can create a weak point where there was none. Findings that support monitoring:

  • The membrane over the blister is intact, with its granules in place.
  • It sits away from seams, flashings, drains, and walking paths.
  • The roof around and beneath it feels firm and dry.
  • Your records show its size has stayed about the same.

Flat roof membrane blister repair is the usual recommendation when a blister has opened, is likely to open, or is tied to water in the roof:

  • The surface is cracked, split, or punctured.
  • The blister reaches a seam or is lifting a lap edge.
  • It has clearly grown between your measurements.
  • It lies in a walking path or where equipment is serviced.
  • Water ponds on it, or the material below feels wet or soft.
  • There are many blisters across the roof, or stains inside the building.

The extent of a repair follows from what is underneath. A blister over dry material can usually be patched in that area. Wet insulation or widespread loss of adhesion calls for a larger section to be opened and rebuilt.

Frequently asked questions about modified bitumen roof blisters

Should I pop a blister on my flat roof?

No. An intact blister still keeps water out, and puncturing it creates an opening in the membrane. If a blister needs attention, a roofer should open, dry, and patch it properly. Leave it untouched until it has been inspected.

Do roof blisters always mean the roof is leaking?

No. Many blisters come from a small void left during installation and never let water into the building. Some do signal moisture entering through a seam or flashing. An inspection of the seams, the surface, and the layers below tells the two apart.

Why do roof blisters look bigger in the afternoon?

The air and moisture trapped in the blister expand as the roof heats up, so the bubble swells in the hottest part of the day and settles when the roof cools. This is normal for a blister. It is also why comparison photos should be taken at a similar time of day.

How often should a low-slope roof with blisters be checked?

Reed Roofing's flat roof maintenance guide suggests inspecting a flat roof at least twice a year and scheduling a professional inspection at least once a year. A roof with known blisters benefits from an extra look after extended hot weather, since heat is what makes blisters grow.

Have Reed Roofing look at your modified bitumen roof

Reed Roofing installs and maintains modified bitumen roofing on low-slope and flat roofs for residential and commercial properties. The company is based in Spring Valley, CA and serves Chula Vista, Eastlake, National City, Imperial Beach, La Mesa, and Spring Valley, with in-person roof assessments and free estimates. To have a blistered area checked, call 619-421-5196 or <a href="https://srreedroofing.com/contact">contact Reed Roofing to request a free estimate</a>, and bring your sketch, measurements, and photos.